LAN Design Project

Packet Tracer
CSCI 356 – 50 points
Scenario:
You have been tasked with designing your new corporate network since they found out you
have studied IP addressing, Cisco networking, and routing. Below is a screen shot of the
topology for your network:
You are responsible for the following tasks:
Design and Implement IPv4 addressing plan
Includes putting addresses on all PCs, switches, and routers
Design and Implement basic configurations for Switch 1 and Switch 2
Hostnames, Management IP address for VLAN 1, enable secret password, line console
password and Message of the Day Warning banner. Put proper default gateway address
on Switch 1 and Switch 2.
Design and Implement basic configurations on all 3 routers:
Hostnames, IP addresses on proper interfaces, enable secret password, line console
password and Message of the Day Warning banner.
Design and Implement SSH on switches
Create proper addressing on VLAN 1, usernames & passwords on Switch 1 and Switch 2
Design and Implement SSH on all 3 routers.
Create usernames & passwords on Corporate Router, ISP router and Branch office
router
Design and Implement static routing on all 3 routers so that all networks are reachable.
Create proper static routes on routers to reach all other networks.
Details on Addressing:
You have been given the following major IP address: _________________________________
NOTE: You will each have your own different major IP address that you need to subnet. In
other words, everyone will have a slightly different problem!
You need to subnet that into 4 separate networks.
Network 1 subnet – Corporate LAN
Network 2 subnet – Connection between Corp Router G0/0 to ISP G0/0
Network 3 subnet – Connection between ISP Router G0/1 to Branch office Router G0/1
Network 4 subnet – Branch Office LAN
Put proper addressing on Corporate Router interfaces G0/0 and G0/1
Put proper addressing on ISP router G0/0 and G0/1
Put proper addressing on Branch Office Router G0/0 and G0/1
Turn on all interfaces on all 3 routers by issuing the no shutdown command for each interface
Put VLAN 1 ip address on Switch 1 – Should be address in Network 1 Corporate LAN subnet
Put VLAN 1 ip address on Switch 2 – should be address in Network 4 Branch office LAN
subnet.
Put proper addressing, subnet mask and default gateway on PCs and Server in Corporate LAN.
They should use addresses in Network 1 subnet.
Put proper addressing, subnet mask and default gateway on PCs in Branch Office LAN. They
should use addresses from Network 4 subnet.
Configure static routing on all 3 routers.
Corporate router will need a route to Branch office LAN and connection between ISP and
Branch router.
ISP router will need a route to Corporate LAN and Branch office LAN
Branch router will need a route to Corporate LAN and connection between ISP and Corp router.
TESTING & VALIDATION
Every device should be able to successfully ping every other device.
Routers should have complete routing tables – that is, they should “see” all 4 networks.
I should be able to ssh into the switches.
COMMON DEVICE CONFIGURATION PARAMETERS –
enable secret command on all routers and switches should be cisco
line console password on all routers and switches should be class
ssh username admin ssh password cisco123
message of the day banner Warning! Stay out unless specifically authorized!
Put in address design. Have instructor check before implanting in Packet Tracer
IP Subnetting Address Design: Fill out information for your four subnets
Subnet
Number Subnet Address
First Usable Host
Address
Last Usable Host
Address
Broadcast
Address
0 1 2 3
Fill out table with proper addresses. Have instructor check before implementing in Packet
Tracer.
Device Interface IP Address Subnet Mask
Corporate Router G0/0
G0/1
ISP Router G0/0
G0/1
Branch Office
Router G0/0
G0/1
Fill out table with proper addresses. Have instructor check before implementing in Packet
Tracer.
Device Interface IP Address Subnet Mask Default Gateway
PC-0 NIC
PC-3 NIC
Server 0 NIC
S1 VLAN 1
PC-1 NIC
PC-2 NIC
S2 VLAN 1
LAN_Design_Project.pdf